embedded - Driving Beaglebone GPIO through /dev/mem

Question

I'm trying to write a C program for blinking a LED on the Beaglebone. I know I can use the sysfs way...but I'd like to see if it is possible to get the same result mapping the physical address space with /dev/mem.

I have a header file, beaglebone_gpio.h wit the following contents:

#ifndef _BEAGLEBONE_GPIO_H_
#define _BEAGLEBONE_GPIO_H_

#define GPIO1_START_ADDR 0x4804C000
#define GPIO1_END_ADDR 0x4804DFFF
#define GPIO1_SIZE (GPIO1_END_ADDR - GPIO1_START_ADDR)
#define GPIO_OE 0x134
#define GPIO_SETDATAOUT 0x194
#define GPIO_CLEARDATAOUT 0x190

#define USR0_LED (1<<21)
#define USR1_LED (1<<22)
#define USR2_LED (1<<23)
#define USR3_LED (1<<24)

#endif

and then I have my C program, gpiotest.c

#include <stdio.h>
#include <stdlib.h>
#include <sys/mman.h>
#include <sys/stat.h>
#include <fcntl.h> 
#include "beaglebone_gpio.h"

int main(int argc, char *argv[]) {
    volatile void *gpio_addr = NULL;
    volatile unsigned int *gpio_oe_addr = NULL;
    volatile unsigned int *gpio_setdataout_addr = NULL;
    volatile unsigned int *gpio_cleardataout_addr = NULL;
    unsigned int reg;
    int fd = open("/dev/mem", O_RDWR);

    printf("Mapping %X - %X (size: %X)
", GPIO1_START_ADDR, GPIO1_END_ADDR, GPIO1_SIZE);

    gpio_addr = mmap(0, GPIO1_SIZE, PROT_READ | PROT_WRITE, MAP_SHARED, fd, GPIO1_START_ADDR);

    gpio_oe_addr = gpio_addr + GPIO_OE;
    gpio_setdataout_addr = gpio_addr + GPIO_SETDATAOUT;
    gpio_cleardataout_addr = gpio_addr + GPIO_CLEARDATAOUT;

    if(gpio_addr == MAP_FAILED) {
        printf("Unable to map GPIO
");
        exit(1);
    }
    printf("GPIO mapped to %p
", gpio_addr);
    printf("GPIO OE mapped to %p
", gpio_oe_addr);
    printf("GPIO SETDATAOUTADDR mapped to %p
", gpio_setdataout_addr);
    printf("GPIO CLEARDATAOUT mapped to %p
", gpio_cleardataout_addr);

    reg = *gpio_oe_addr;
    printf("GPIO1 configuration: %X
", reg);
    reg = reg & (0xFFFFFFFF - USR1_LED);
    *gpio_oe_addr = reg;
    printf("GPIO1 configuration: %X
", reg);

    printf("Start blinking LED USR1
");
    while(1) {
        printf("ON
");
        *gpio_setdataout_addr= USR1_LED;
        sleep(1);
        printf("OFF
");
        *gpio_cleardataout_addr = USR1_LED;
        sleep(1);
    }

    close(fd);
    return 0;
}

The output is:

Mapping 4804C000 - 4804DFFF (size: 1FFF)
GPIO mapped to 0x40225000
GPIO OE mapped to 40225134
GPIO SEDATAOUTADDR mapped to 0x40225194
GPIO CLEARDATAOUTADDR mapped to 0x40225190
GPIO1 configuration: FE1FFFFF
GPIO1 configuratino: FE1FFFFF
Start blinking LED USR1
ON
OFF
ON
OFF
...

but I can't see the led blinking.

As you can see from the output of the program the configuration is correct, FE1FFFFF, is coherent since GPIO1_21, GPIO1_22, GPIO1_23 and GPIO1_24 are configured as outputs, each one driving a LED.

Any idea about the reason?

Answer 1

Be careful. This works at first blush, but it directly writes to a register that the GPIO controller driver believes it owns. It will cause odd and hard to track down side effects, either on this GPIO line or on a GPIO that is in the same bank. For this to work reliably you need to disable the entire bank from the kernel GPIO driver.